| SIRIUS ACT with PROFINET: Standard interface module 24V DC, screw terminal, Front plate mounting 1 to 20 terminal modules connectable |
Product brand name | SIRIUS ACT |
Product designation | Interface module |
Product type designation | 3SU1 |
Display |
Display version | |
for diagnostic function: Supply voltage monitoring Power LED | Yes |
status Tx/Rx link | Yes |
General technical data |
Product function | |
Reverse polarity protection | Yes |
Diagnostics function | Yes |
Alarms | Yes |
I&M data | Yes; I&M0 ... I&M3 |
Firmware version | 1.0.0 |
Hardware version | 1 |
Configuration function with dataset | Yes |
Software version with STEP 7 in the TIA Portal required | Integrated in TIA Portal Version 14 SP1 or higher (HSP for V13 and V14) |
Number of units per rack maximum | 20 |
Number of submodules per station maximum | 24 |
Power loss [W] typical | 0.67 W |
Insulation voltage rated value | 30 V |
Degree of pollution | 3 |
Type of voltage | |
of the operating voltage | DC |
of the input voltage | DC |
Surge voltage resistance rated value | 0.8 kV |
Consumed current | |
maximum | 100 mA |
Rated value | 28 mA |
Protection class IP | IP20 |
Reference code acc. to DIN EN 81346-2 | K |
Operating voltage rated value | 20.4 V |
I2t value | 0.008 A²·s |
Supply voltage |
Supply voltage at DC Rated value | 24 V |
Communication/ Protocol |
Product function at the Ethernet interface | |
Autocrossover | Yes |
Autonegotiation | Yes |
Protocol at the 1st interface | |
media redundancy protocol | No |
Product function at the 1st interface | |
PROFINET IO device | Yes |
Product function of the PROFINET IO device is supported PROFINET system redundancy (S2) | No |
Service as PROFINET IO device | |
prioritized startup | No |
isochronous mode | No |
supports Shared Device | No |
supports PROFIenergy | No |
IRT | No |
MRP | No |
MRPD | No |
Service for open IE communication | |
LLDP | Yes |
SNMP | Yes |
TCP/IP | Yes |
GSD version/revision with PROFINET required | V2.3 |
Transmission mode for Industrial Ethernet | PROFINET with 100 Mbps full duplex (100BASE-TX) |
Network load class acc. to PROFINET | 1 |
Specification for Security Level 1 test acc. to PROFINET | Resilient to network loading |
Control circuit/ Control |
Inrush current maximum | 16 A |
Galvanic isolation |
Galvanic isolation between PROFINET and all other circuits | Yes |
Inputs/ Outputs |
Number of digital inputs | 0 |
safety-related | 0 |
Number of digital outputs | 0 |
Connections/Terminals |
Type of electrical connection | screw-type terminals |
Connectable conductor cross-section for auxiliary contacts | |
single or multi-stranded | 0.2 ... 2.5 mm² |
finely stranded with core end processing | 2.5 mm² |
Connectable conductor cross-section | |
solid | 0.2 ... 2.5 mm² |
solid with core end processing | 0.2 ... 2.5 mm² |
finely stranded with core end processing | 0.25 ... 2.5 mm² |
finely stranded without core end processing | 0.2 ... 2.5 mm² |
AWG number as coded connectable conductor cross section | 30 ... 12 |
Tightening torque with screw-type terminals | 0.5 ... 0.6 N·m |
Safety related data |
Service life maximum | 20 y |
Design of the interface | |
Ethernet interface | Yes; for Ethernet services |
Fast Ethernet interface | Yes; PROFINET with 100 Mbps |
Interface design 1 | |
integrated switch | No |
RJ45 (Ethernet) | Yes |
Number of ports at the 1st interface | 1 |
Number of interfaces acc. to PROFINET | 1 |
Ambient conditions |
Ambient temperature | |
during operation | -25 ... +60 °C |
during storage | -40 ... +80 °C |
Environmental category during operation acc. to IEC 60721 | 3M6, 3S2, 3B2, 3K6 (with relative air humidity of 10 ... 95 %, no condensation in operation permitted) |
Explosion protection marking for intrinsic safety of related equipment EEx ia | No |
Explosion protection marking for intrinsic safety of related equipment EEx ib | No |
Installation/ mounting/ dimensions |
Mounting type of modules and accessories | Snap-on mounting |
Height | 80.1 mm |
Width | 40 mm |
Depth | 72.1 mm |