| SIPLUS ET 200S EM 2RO 24 V DC-230 V AC/5 A -25...+70°C based on 6ES7132-4HB01-0AB0 5 units per packing unit . 5 electronic modules for ET 200S, 2 DO relay 24 V DC-230 V AC/5 A, 15 mm width, Substitute value output with LED SF (group fault) |
| Supply voltage |
| Load voltage L+ |
| Rated value (DC) | 24 V; From power module |
| Reverse polarity protection | Yes |
| Input current |
| from load voltage L+ (without load), max. | 30 mA |
| from backplane bus 3.3 V DC, max. | 10 mA |
| Power loss |
| Power loss, typ. | 0.6 W |
| Address area |
| Address space per module |
| Address space per module, max. | 1 byte |
| with packing | 2 bit |
| Digital outputs |
| Number of digital outputs | 2 |
| Short-circuit protection | No |
| Limitation of inductive shutdown voltage to | No |
| Controlling a digital input | Yes |
| Output current |
| for signal "1" rated value | 5 A |
| for signal "1" minimum load current | 8 mA |
| Parallel switching of two outputs |
| for uprating | No |
| for redundant control of a load | No |
| Switching frequency |
| with resistive load, max. | 2 Hz |
| with inductive load, max. | 0.5 Hz |
| on lamp load, max. | 2 Hz |
| Relay outputs |
| Switching capacity of contacts |
| — Thermal continuous current, max. | 5 A |
| Cable length |
| shielded, max. | 1 000 m |
| unshielded, max. | 600 m |
| Isochronous mode |
| Isochronous operation (application synchronized up to terminal) | No |
| Interrupts/diagnostics/status information |
| Diagnostics function | No |
| Substitute values connectable | Yes; 0/1 |
| Diagnostics indication LED |
| Status indicator digital output (green) | Yes |
| Parameter |
| Remark | 3 byte |
| Response to CPU/master STOP | Substitute a value/keep last value |
| Potential separation |
| Potential separation digital outputs |
| between the channels | Yes |
| between the channels and backplane bus | Yes |
| Between the channels and load voltage L+ | Yes |
| Isolation |
| tested with |
| Channels against backplane bus and load voltage L+ | 1500 V AC |
| Load voltage L+ against backplane bus | 500 V DC |
| Ambient conditions |
| Ambient temperature during operation |
| min. | -25 °C; = Tmin |
| max. | 70 °C; = Tmax |
| Altitude during operation relating to sea level |
| Installation altitude above sea level, max. | 2 000 m |
| Ambient air temperature-barometric pressure-altitude | Tmin ... Tmax at 1 140 hPa ... 795 hPa (-1 000 m ... +2 000 m) |
| Relative humidity |
| With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; RH incl. condensation/frost (no commissioning under condensation conditions) |
| Resistance |
| Use in stationary industrial systems |
| — to biologically active substances according to EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request |
| — to chemically active substances according to EN 60721-3-3 | Yes; Class 3C4 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); * |
| — to mechanically active substances according to EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust, * |
| Use on ships/at sea |
| — to biologically active substances according to EN 60721-3-6 | Yes; Class 6B2 mold and fungal spores (excluding fauna); Class 6B3 on request |
| — to chemically active substances according to EN 60721-3-6 | Yes; Class 6C3 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); * |
| — to mechanically active substances according to EN 60721-3-6 | Yes; Class 6S3 incl. sand, dust; * |
| Remark |
| — Note regarding classification of environmental conditions acc. to EN 60721 | * The supplied plug covers must remain in place over the unused interfaces during operation! |
| Dimensions |
| Width | 15 mm |
| Height | 81 mm |
| Depth | 52 mm |
| Weights |
| Weight, approx. | 50 g |
| last modified: | 03/25/2019 |
