| SIPLUS ET 200S EM 2AI RTD HF -25...+60°C based on 6ES7134-4NB51-0AB0 |
| Supply voltage |
| Load voltage L+ |
| Rated value (DC) | 24 V; From power module |
| Reverse polarity protection | Yes |
| Input current |
| from load voltage L+ (without load), max. | 30 mA |
| from backplane bus 3.3 V DC, max. | 10 mA |
| Power loss |
| Power loss, typ. | 0.6 W |
| Address area |
| Address space per module |
| Address space per module, max. | 4 byte |
| Analog inputs |
| Number of analog inputs | 2 |
| permissible input voltage for voltage input (destruction limit), max. | 9 V |
| Constant measurement current for resistance-type transmitter, typ. | 1.25 mA |
| Cycle time (all channels) max. | Number of active channels per module x basic conversion time |
| Technical unit for temperature measurement adjustable | Yes |
| Input ranges (rated values), resistance thermometer |
| Cu 10 | Yes |
| Input resistance (Cu 10) | 10 MΩ |
| Ni 100 | Yes |
| Input resistance (Ni 100) | 10 MΩ |
| Ni 1000 | Yes |
| Input resistance (Ni 1000) | 10 MΩ |
| Ni 120 | Yes |
| Input resistance (Ni 120) | 10 MΩ |
| Ni 200 | Yes |
| Input resistance (Ni 200) | 10 MΩ |
| Ni 500 | Yes |
| Input resistance (Ni 500) | 10 MΩ |
| Pt 100 | Yes |
| Input resistance (Pt 100) | 10 MΩ |
| Pt 1000 | Yes |
| Input resistance (Pt 1000) | 10 MΩ |
| Pt 200 | Yes |
| Input resistance (Pt 200) | 10 MΩ |
| Pt 500 | Yes |
| Input resistance (Pt 500) | 10 MΩ |
| Input ranges (rated values), resistors |
| 0 to 150 ohms | Yes |
| Input resistance (0 to 150 ohms) | 10 MΩ |
| 0 to 300 ohms | Yes |
| Input resistance (0 to 300 ohms) | 10 MΩ |
| 0 to 600 ohms | Yes |
| Input resistance (0 to 600 ohms) | 10 MΩ |
| 0 to 3000 ohms | Yes |
| Input resistance (0 to 3000 ohms) | 10 MΩ |
| Thermocouple (TC) |
| Temperature compensation |
| — internal temperature compensation | Yes |
| Characteristic linearization |
| parameterizable | Yes; for Ptxxx, Nixxx |
| — for resistance thermometer | Ptxxx, Nixxx |
| Cable length |
| shielded, max. | 200 m |
| Analog value generation for the inputs |
| Measurement principle | integrating (Sigma-Delta) |
| Integration and conversion time/resolution per channel |
| Resolution with overrange (bit including sign), max. | 16 bit; for Pt100, Ni100, Ni120, Pt200, Ni200, Pt500, Ni500, Pt1000, Ni1000, Cu10: 15 bit + sign; for 150, 300, 600, 3000 ohms: 15 bit; for PTC: 1 bit |
| Integration time (ms) | 16,7 / 20 ms |
| Interference voltage suppression for interference frequency f1 in Hz | 50 / 60 Hz |
| Conversion time (per channel) | Basic conversion time incl. integration time: 50 / 60 ms; additional conversion time for diagnostics of wire break test: 5 / 5 ms; additional conversion time for line compensation with 3-wire connection: 50 / 60 ms |
| Smoothing of measured values |
| parameterizable | Yes; In four stages by means of digital filtering |
| Step: None | Yes; 1x cycle time |
| Step: low | Yes; 4x cycle time |
| Step: Medium | Yes; 32x cycle time |
| Step: High | Yes; 64x cycle time |
| Encoder |
| Connection of signal encoders |
| for resistance measurement with two-wire connection | Yes |
| for resistance measurement with three-wire connection | Yes; internal compensation of the line resistances |
| for resistance measurement with four-wire connection | Yes |
| Errors/accuracies |
| Linearity error (relative to input range), (+/-) | 0.01 % |
| Temperature error (relative to input range), (+/-) | 0.0009 %/K |
| Crosstalk between the inputs, min. | -50 dB |
| Repeat accuracy in steady state at 25 °C (relative to input range), (+/-) | 0.05 % |
| Operational error limit in overall temperature range |
| Resistance thermometer, relative to input range, (+/-) | Resistance-type transmitter: ±0.1 %; Pt100, Pt200, Pt500, Pt1000 standard: ±1.0 K; Pt100, Pt200, Pt500, Pt1000 climate: ±0.25 K; Ni100, Ni120, Ni200, Ni500, Ni1000 standard and climate: ±0.4 K; Cu10 ±1.5 K |
| Basic error limit (operational limit at 25 °C) |
| Resistance thermometer, relative to input range, (+/-) | Resistance-type transmitter: ±0.05 %; Pt100, Pt200, Pt500, Pt1000 standard: ±0.6 K; Pt100, Pt200, Pt500, Pt1000 climate: ±0.13 K; Ni100, Ni120, Ni200, Ni500, Ni1000 standard and climate: ±0.2 K; Cu10 ±1 K |
| Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency |
| Series mode interference (peak value of interference < rated value of input range), min. | 70 dB |
| Common mode interference (USS < 2.5 V) , min. | 90 dB |
| Isochronous mode |
| Isochronous operation (application synchronized up to terminal) | No |
| Interrupts/diagnostics/status information |
| Diagnostic messages |
| Wire-break | Yes |
| Group error | Yes |
| Overflow/underflow | Yes |
| Diagnostics indication LED |
| Group error SF (red) | Yes |
| Parameter |
| Remark | 7 byte |
| Diagnostics wire break | Disable / enable |
| Measurement type/range | Deactivated/ 150 Ohm / 300 Ohm / 600 Ohm /Pt100/Pt200/Pt500/Pt1000 each standard or climate range / Ni100/Ni120/Ni200/Ni500/Ni1000 each standard or climate range / Cu10 each standard or climate range / PTC |
| Group diagnostics | Disable / enable |
| Overflow/underflow | Disable / enable |
| Potential separation |
| Potential separation analog inputs |
| between the channels | No |
| between the channels and backplane bus | Yes |
| Between the channels and load voltage L+ | Yes |
| Permissible potential difference |
| between MANA and M internally (UISO) | 75 V DC/60 V AC |
| Isolation |
| Isolation tested with | 500 V DC |
| Standards, approvals, certificates |
| CE mark | Yes |
| Ambient conditions |
| Ambient temperature during operation |
| min. | -25 °C; = Tmin |
| max. | 60 °C; = Tmax |
| Altitude during operation relating to sea level |
| Installation altitude above sea level, max. | 5 000 m |
| Ambient air temperature-barometric pressure-altitude | Tmin ... Tmax at 1 140 hPa ... 795 hPa (-1 000 m ... +2 000 m) // Tmin ... (Tmax - 10 K) at 795 hPa ... 658 hPa (+2 000 m ... +3 500 m) // Tmin ... (Tmax -20 K) at 658 hPa ... 540 hPa (+3 500 m ... +5 000 m) |
| Relative humidity |
| With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; RH incl. condensation/frost permitted (no commissioning in bedewed state) |
| Resistance |
| Use in stationary industrial systems |
| — to biologically active substances according to EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request |
| — to chemically active substances according to EN 60721-3-3 | Yes; Class 3C4 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); * |
| — to mechanically active substances according to EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust, * |
| Use on ships/at sea |
| — to biologically active substances according to EN 60721-3-6 | Yes; Class 6B2 mold and fungal spores (excluding fauna); Class 6B3 on request |
| — to chemically active substances according to EN 60721-3-6 | Yes; Class 6C3 (RH < 75 %) incl. salt spray acc. to EN 60068-2-52 (severity degree 3); * |
| — to mechanically active substances according to EN 60721-3-6 | Yes; Class 6S3 incl. sand, dust; * |
| Remark |
| — Note regarding classification of environmental conditions acc. to EN 60721 | * The supplied plug covers must remain in place over the unused interfaces during operation! |
| Dimensions |
| Width | 15 mm |
| Height | 81 mm |
| Depth | 52 mm |
| Weights |
| Weight, approx. | 40 g |
| last modified: | 03/29/2019 |
