| ***Spare part*** SIPLUS ET 200S F-DO 24 V PROFIsafe -25...+60 °C with conformal coating based on 6ES7138-4FB03-0AB0 |
| Supply voltage |
| Load voltage L+ |
| Rated value (DC) | 24 V |
| Reverse polarity protection | No |
| Input current |
| From load voltage L+ (no load), typ. | 100 mA |
| from backplane bus 3.3 V DC, max. | 28 mA |
| Power loss |
| Power loss, typ. | 3.5 W |
| Digital outputs |
| Number of digital outputs | 4 |
| Short-circuit protection | Yes |
| Limitation of inductive shutdown voltage to | Typ. (2L+) -47 V |
| Controlling a digital input | No |
| Switching capacity of the outputs |
| on lamp load, max. | 10 W |
| Load resistance range |
| lower limit | 12 Ω |
| upper limit | 1 kΩ |
| Output voltage |
| for signal "1", min. | L+ (-2,0 V), current sourcing switch: L+ (-1,5 V), voltage drop on current sinking switch: max. 0.5 V |
| Output current |
| for signal "1" rated value | 2 A |
| for signal "1" permissible range, min. | 20 mA |
| for signal "1" permissible range, max. | 2.4 A |
| for signal "0" residual current, max. | 0.5 mA; Current-sourcing: max. 0.5 mA; Current sinking: max. 4 mA |
| Parallel switching of two outputs |
| for uprating | No |
| for redundant control of a load | No |
| Switching frequency |
| with resistive load, max. | 30 Hz |
| with inductive load, max. | 0.1 Hz |
| on lamp load, max. | 10 Hz |
| Total current of the outputs |
| Current per module, max. | 6 A |
| Total current of the outputs (per group) |
| horizontal installation |
| — up to 40 °C, max. | 6 A |
| — up to 55 °C, max. | 5 A |
| — up to 60 °C, max. | 4 A |
| vertical installation |
| — up to 40 °C, max. | 4 A |
| Cable length |
| shielded, max. | 200 m |
| unshielded, max. | 200 m |
| Interrupts/diagnostics/status information |
| Diagnostics function | Yes |
| Diagnostic messages |
| Wire-break | Yes |
| Short-circuit | Yes |
| Diagnostics indication LED |
| Group error SF (red) | Yes |
| Status indicator digital output (green) | Yes |
| Potential separation |
| Potential separation digital outputs |
| between the channels | No |
| between the channels and backplane bus | Yes |
| Between the channels and load voltage L+ | No |
| Isolation |
| Isolation tested with | 500 V DC |
| tested with |
| Channels against backplane bus and load voltage L+ | 1500 V AC |
| Standards, approvals, certificates |
| Highest safety class achievable in safety mode |
| acc. to EN 954 | 4 |
| Performance level according to ISO 13849-1 | e |
| SIL acc. to IEC 61508 | SIL 3 |
| Ambient conditions |
| Ambient temperature during operation |
| min. | -25 °C; = Tmin |
| max. | 60 °C; = Tmax |
| Altitude during operation relating to sea level |
| Ambient air temperature-barometric pressure-altitude | Tmin ... Tmax at 1 080 hPa ... 795 hPa (-1 000 m ... +2 000 m) |
| Relative humidity |
| With condensation, tested in accordance with IEC 60068-2-38, max. | 100 %; RH incl. condensation/frost (no commissioning under condensation conditions) |
| Resistance |
| Use in stationary industrial systems |
| — to biologically active substances according to EN 60721-3-3 | Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request |
| — to chemically active substances according to EN 60721-3-3 | Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation! |
| — to mechanically active substances according to EN 60721-3-3 | Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation! |
| Dimensions |
| Width | 30 mm |
| Height | 81 mm |
| Depth | 52 mm |
| Weights |
| Weight, approx. | 85 g |
| last modified: | 03/13/2019 |
