| SIPLUS LOGO! POWER 24V 1,3A |
| ***Spare Part*** SIPLUS LOGO! Power 24 V 1.3 A for medial exposure -25...+70°C based on 6EP1331-1SH03 . stabilized power supply input 24 V DC/1.3 A |
| Input |
| Input | 1-phase AC or DC |
| Rated voltage value Vin rated | 100 ... 240 V |
| Voltage range AC | 85 ... 264 V |
| Input voltage | |
| at DC | 110 ... 300 V |
| Wide-range input | Yes |
| Overvoltage resistance | 2.3 × Vin rated, 1.3 ms |
| Mains buffering at Iout rated, min. | 40 ms; at Vin = 187 V |
| Rated line frequency 1 | 50 Hz |
| Rated line frequency 2 | 60 Hz |
| Rated line range | 47 ... 63 Hz |
| Input current | |
| at rated input voltage 120 V | 0.7 A |
| at rated input voltage 230 V | 0.35 A |
| Switch-on current limiting (+25 °C), max. | 25 A |
| I²t, max. | 0.8 A²·s |
| Built-in incoming fuse | internal |
| Protection in the mains power input (IEC 898) | Recommended miniature circuit breaker: from 6 A characteristic B or from 2 A characteristic C |
| Output |
| Output | Controlled, isolated DC voltage |
| Rated voltage Vout DC | 24 V |
| Total tolerance, static ± | 3 % |
| Static mains compensation, approx. | 0.1 % |
| Static load balancing, approx. | 1.5 % |
| Residual ripple peak-peak, max. | 200 mV |
| Residual ripple peak-peak, typ. | 10 mV |
| Spikes peak-peak, max. (bandwidth: 20 MHz) | 300 mV |
| Spikes peak-peak, typ. (bandwidth: 20 MHz) | 20 mV |
| Adjustment range | 22.2 ... 26.4 V |
| Product function Output voltage adjustable | Yes |
| Output voltage setting | via potentiometer |
| Status display | Green LED for output voltage OK |
| On/off behavior | No overshoot of Vout (soft start) |
| Startup delay, max. | 0.5 s |
| Voltage rise, typ. | 15 ms |
| Rated current value Iout rated | 1.3 A |
| Current range | 0 ... 1.3 A |
| Note | +55 ... +70 °C: Derating 2%/K |
| Supplied active power typical | 30 W |
| Parallel switching for enhanced performance | Yes |
| Numbers of parallel switchable units for enhanced performance | 2 |
| Efficiency |
| Efficiency at Vout rated, Iout rated, approx. | 85 % |
| Power loss at Vout rated, Iout rated, approx. | 6 W |
| Closed-loop control |
| Dynamic mains compensation (Vin rated ±15 %), max. | 0.2 % |
| Dynamic load smoothing (Iout: 10/90/10 %), Uout ± typ. | 1 % |
| Load step setting time 10 to 90%, typ. | 1 ms |
| Load step setting time 90 to 10%, typ. | 1 ms |
| Protection and monitoring |
| Output overvoltage protection | Yes, according to EN 60950-1 |
| Current limitation, typ. | 1.7 A |
| Property of the output Short-circuit proof | Yes |
| Short-circuit protection | Constant current characteristic |
| Enduring short circuit current RMS value | |
| maximum | 2.4 A |
| Overload/short-circuit indicator | - |
| Safety |
| Primary/secondary isolation | Yes |
| Galvanic isolation | Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 |
| Protection class | Class II (without protective conductor) |
| CE mark | Yes |
| Degree of protection (EN 60529) | IP20 |
| EMC |
| Emitted interference | EN 55022 Class B |
| Supply harmonics limitation | not applicable |
| Noise immunity | EN 61000-6-2 |
| Operating data |
| Ambient temperature | |
| during operation | -40 ... +70 °C |
| — Note | with natural convection |
| during transport | -40 ... +85 °C |
| during storage | -40 ... +85 °C |
| Ambient condition relating to ambient temperature - air pressure - installation altitude | Tmin ... Tmax at 1140 hPa ... 795 hPa (-1000 m ... +2000 m); Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m); Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m) |
| Relative humidity with condensation maximum | 100 %; Relative humidity, incl. condensation/frost permitted (no commissioning under condensation conditions) |
| Resistance to biologically active substances conformity acc. to EN 60721-3-3 | Yes; Conformity with EN 60721-3-3, Class 3B2 mold, fungus and dry rot spores (with the excepion of fauna). The supplied connector covers must remain on the unused interfaces during operation! |
| Resistance to chemically active substances conformity acc. to EN 60721-3-3 | Yes; Conformity with EN 60721-3-3, Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation! |
| Resistance to mechanically active substances conformity acc. to EN 60721-3-3 | Yes; Conformity with EN 60721-3-3, Class 3S4 incl. Sand, dust. The supplied connector covers must remain on the unused interfaces during operation! |
| Mechanics |
| Connection technology | screw-type terminals |
| Connections | |
| Supply input | L, N: 1 screw terminal each for 0.5 ... 2.5 mm2 single-core/finely stranded |
| Output | +, -: 2 screw terminals each for 0.5 ... 2.5 mm² |
| Auxiliary | - |
| Width of the enclosure | 54 mm |
| Height of the enclosure | 90 mm |
| Depth of the enclosure | 55 mm |
| Required spacing | |
| top | 20 mm |
| bottom | 20 mm |
| left | 0 mm |
| right | 0 mm |
| Weight, approx. | 0.17 kg |
| Product feature of the enclosure housing for side-by-side mounting | Yes |
| Installation | Snaps onto DIN rail EN 60715 35x7.5/15 |
| Other information | Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified) |
| |
