| SIMATIC ET 200SP HA, digital input module, DI 16XNAMUR HA, suitable for terminal block H1, M1, color code CC01, channel diagnostics |
| General information |
| Product type designation | DI 16xNAMUR HA |
| Firmware version | V1.0 |
| FW update possible | Yes |
| Usable terminal block | TB type H1, M1 and N0 |
| Color code for module-specific color identification plate | CC01 |
| Product function |
| I&M data | Yes; I&M0 to I&M3 |
| Engineering with |
| PCS 7 configurable/integrated as of version | V9.0 |
| Operating mode |
| DI | Yes |
| Counter | No |
| Redundancy |
| Redundancy capability | Yes; With TB type M1 |
| Supply voltage |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 19.2 V |
| permissible range, upper limit (DC) | 28.8 V |
| Reverse polarity protection | Yes |
| Input current |
| Current consumption (rated value) | 95 mA |
| Current consumption, max. | 115 mA |
| Encoder supply |
| Number of outputs | 16 |
| Output voltage encoder supply, min. | 8.1 V |
| Short-circuit protection | Yes |
| Power |
| Power available from the backplane bus | 74 mW |
| Power loss |
| Power loss, typ. | 2.4 W |
| Address area |
| Address space per module |
| Address space per module, max. | 2 byte; + 2 bytes for QI information |
| Digital inputs |
| Number of digital inputs | 16; NAMUR |
| Digital inputs, parameterizable | Yes |
| Pulse extension | Yes; 0.5 s, 1 s, 2 s |
| Time stamping | Yes |
| Time stamp (with precision of 1 ms) | No |
| Edge evaluation | Yes; rising edge, falling edge, edge change |
| Signal change flutter | Yes; 2 to 32 signal changes |
| Flutter observation window | Yes; 0.5 s, 1 s to 100 s in 1-s steps |
| Input voltage |
| Rated value (DC) | 8.2 V |
| Input current |
| for 10 k switched contact |
| — for signal "0" | 0.35 to 1.2 mA |
| — for signal "1" | 2.1 ... 6.4 mA |
| for unswitched contact |
| — for signal "0", max. (permissible quiescent current) | 0.5 mA |
| — for signal "1" | typ. 8 mA |
| for NAMUR encoders |
| — for signal "0" | 0.35 to 1.2 mA |
| — for signal "1" | 2.1 ... 6.4 mA |
| Input delay (for rated value of input voltage) |
| tolerated changeover time for changeover contacts | 300 ms |
| for NAMUR inputs |
| — at "0" to "1", max. | 17 ms |
| — at "1" to "0", max. | 25 ms |
| Cable length |
| shielded, max. | 600 m |
| unshielded, max. | 200 m |
| Encoder |
| Connectable encoders |
| NAMUR encoder/changeover contact according to EN 60947 | Yes |
| Single contact / changeover contact unconnected | Yes |
| Single contact / changeover contact connected with 10 kΩ | Yes |
| 2-wire sensor | Yes; Acc. to NAMUR |
| — permissible quiescent current (2-wire sensor), max. | 1.2 mA |
| Interrupts/diagnostics/status information |
| Alarms |
| Diagnostic alarm | Yes; channel by channel |
| Hardware interrupt | Yes; Parameterizable, channels 0 to 15, rising/falling edge |
| Diagnostic messages |
| Diagnostic information readable | Yes |
| Monitoring the supply voltage | Yes |
| — parameterizable | Yes |
| Monitoring of encoder power supply | Yes |
| Wire-break | Yes |
| Short-circuit | Yes |
| Group error | Yes |
| Changeover contact error | Yes |
| Diagnostics indication LED |
| MAINT LED | Yes; yellow LED |
| Monitoring of the supply voltage (PWR-LED) | Yes; green PWR LED |
| Channel status display | Yes; Green LED |
| for channel diagnostics | Yes; Red LED |
| for module diagnostics | Yes; green/red DIAG LED |
| Potential separation |
| Potential separation channels |
| between the channels | No |
| between the channels and backplane bus | Yes |
| Between the channels and load voltage L+ | Yes |
| Isolation |
| Isolation tested with | 1 500 V DC/1 min, type test |
| Ambient conditions |
| Ambient temperature during operation |
| horizontal installation, min. | -40 °C |
| horizontal installation, max. | 70 °C |
| vertical installation, min. | -40 °C |
| vertical installation, max. | 60 °C |
| Dimensions |
| Width | 22.5 mm |
| Height | 115 mm |
| Depth | 138 mm |
| Weights |
| Weight, approx. | 153 g |
| last modified: | 03/08/2019 |
